RECON Wellness title card reading PEMF Mat Guide, for the PEMF mat guide

PEMF Mat Guide: How to Choose and Use an Infrared PEMF Mat

This guide covers what a PEMF mat is, which specs are worth paying attention to, how we run a session, and what drives the price. No hype. Just how it works and how to fit it into a routine.

Quick answer: A PEMF mat is a full-body surface with built-in copper coils that send a pulsing electromagnetic field at a frequency you choose. An infrared PEMF mat adds a far infrared heat layer to the same surface.

"The best recovery tool is the one that's easy enough to become part of your day."

1 to 30
Hz on both Renew mats
6 / 8
Copper coils, Renew / Renew+
70°C
Top of the heat range

Why We Built Around the Mat

The tools you actually use are the ones that are easy.

I'm Andy, and I built RECON Wellness after a lot of years as an athlete and five labral surgeries. Recovery stopped being optional for me a long time ago. What I learned is simple: the tools you actually use are the ones that are easy. You lie down, you press a button, and it becomes part of your day.

A PEMF mat is one of those tools for us.

This post is general information about our products and how we use them. It is not medical advice. Talk to your doctor before starting any new wellness routine.

What a PEMF Mat Is

Coils, a frequency and an optional heat layer.

PEMF stands for pulsed electromagnetic field. A PEMF mat is a full-body surface with copper coils built in. The coils send a pulsing field at a frequency you pick, measured in hertz (Hz). An infrared PEMF mat (you'll also see it called a PEMF infrared mat) adds a far infrared heat layer, so the same surface also gets warm.

You lay it flat on a bed or the floor, plug it in, choose a frequency, set the heat and a timer, and lie down. That's it. There's nothing to strap on and nothing to set up beyond the controller.

Overhead view of the RECON Renew PEMF Mat laid flat
The Renew PEMF Mat, laid flat and ready for a session.

On our Renew PEMF mat, the heat runs through a layer of amethyst and tourmaline under a PU leather cover. On the Renew+ PEMF Mat, there's also a 660 nm red light layer and a negative ion setting. More on the differences below, and you can see the whole line on our Renew PEMF page.

PEMF Mat Specs That Matter

When you compare PEMF mats, the spec sheet is where the real differences show up. Here's what we look at and what our mats run.

Spec Renew Renew+
Frequency 1 to 30 Hz, 30 settings 1 to 30 Hz, 1 Hz steps
Presets 4 None, keeps last setting
Coils 6 copper 8 copper
Field strength 3 Gauss 3 Gauss
Heat 0 to 70°C (32 to 158°F) 30 to 70°C (86 to 158°F)
Size 72.8 x 29.5 x 1 in 72.8 x 27.5 x 1 in
Weight 37.4 lb (17 kg) 34.4 lb (15.6 kg)
Power 110 to 120 V AC, 280 W 110 to 120 V AC, 280 W

Frequency range and steps

Frequency is the pulse rate of the field. What you want is control: a usable range, small steps, and a few presets so you don't have to think about it every time.

The Renew mat runs 1 to 30 Hz with 30 individual settings, so you can step through it 1 Hz at a time. It also has four presets for quick setup:

  • 3 Hz Wind-Down
  • 8 Hz Unwind
  • 10 Hz Everyday
  • 23 Hz Pre-Training

The Renew+ PEMF Mat runs the same 1 to 30 Hz range in 1 Hz steps. It doesn't have presets; you step to the frequency you want, and the controller keeps your last setting. If you want the details on when we use each one, read PEMF Presets Explained.

Coil count

More coils spread the field across more of the mat. The Renew has 6 copper coils. The Renew+ has 8. Both are full-body mats, so you're lying on coils from your shoulders to your legs.

Field strength

Both Renew mats are rated at 3 Gauss. That's the spec number to compare when you're reading other mats' listings.

Heat range

Heat is the part most people notice first. On the Renew, heat is adjustable from 0 to 70°C (32 to 158°F), so you can run PEMF with no heat at all or go warm. On the Renew+, the heat range is 30 to 70°C (86 to 158°F). Most nights I keep it on the lower end. It's relaxing, and you don't need max heat to enjoy it.

Size and weight

A full-body PEMF mat should fit you lying down with room to spare.

  • Renew: 72.8 x 29.5 x 1 in (185 x 75 x 2.5 cm), 37.4 lb (17 kg)
  • Renew+: 72.8 x 27.5 x 1 in (185 x 70 x 2.5 cm), 34.4 lb (15.6 kg)

Both fit on a twin bed or a spot on the floor.

Power and controller

Both mats run on 110 to 120 V AC at 280 W. The Renew has a digital controller where you pick a preset or step through each Hz setting, then set heat and the timer. The Renew+ has a digital touchscreen for PEMF, heat and light settings. Both carry CE, FCC and RoHS certifications.

RECON Renew+ PEMF Mat controller with temperature, timer, and PEMF frequency buttons
The Renew+ controller: frequency, heat and timer in one place.

Infrared PEMF Mat vs PEMF Only

Same field. Add warmth if you want it.

A PEMF only mat gives you the pulsing field and nothing else. An infrared PEMF mat adds warmth to the same session.

For us, the heat is about feel and routine. A warm surface after a long day makes it easy to lie down and stay there for 30 minutes. In the morning, with the heat low or off, it's a quick session before training. Having both in one surface means one thing to plug in and one session instead of two.

If you're comparing PEMF mats, check whether the heat can go all the way down. Being able to run with zero heat on the Renew is useful on hot days or right before a workout.

How to Run a PEMF Mat Session

Here's how we do it at RECON Wellness. Keep it simple.

  1. Lay the mat flat on a bed or the floor, cover side up.
  2. Plug in the controller and turn it on.
  3. Pick a frequency. On the Renew, use a preset or step through by 1 Hz. On the Renew+, step to the frequency you want.
  4. Set the heat. Start low. You can always turn it up.
  5. Set the timer. We run 20 to 40 minutes on the Renew. The Renew+ lets you pick 20 to 60 minutes.
  6. Lie down and relax. Phone away if you can.

Frequency by time of day

We pick presets by the time of day and what's next (on the Renew+, dial in the same frequency by hand):

Morning or before training
23 Hz Pre-Training, heat low or off, as part of your warm-up.
Midday
10 Hz Everyday, moderate heat, a reset between meetings or after a workout.
Evening
8 Hz Unwind or 3 Hz Wind-Down, warmer heat, part of your wind-down.

These are routine choices, not prescriptions. Try them and see what feels right to you. For more on the reasoning behind each preset, see PEMF Presets Explained, and for how a PEMF mat fits into our bigger picture, read PEMF Is Not Magic.

Using a PEMF Mat for Sleep Routines

Part of the wind-down, not all night.

A lot of people search for a pemf mat for sleeping. Here's how we think about it: the mat is a good fit as part of an evening wind-down routine, not as something you sleep on all night.

What that looks like in my house:

  • Lay the Renew on the bed or the floor an hour or so before bed.
  • Pick 3 Hz Wind-Down.
  • Set the heat to a comfortable warm.
  • Set the timer for 20 to 30 minutes so it shuts itself off.
  • Lights low, screens off, just lie there.

The timer is the key. You lie down, it runs, it stops. It becomes a habit, the same way stretching or reading before bed does. We're not making any promises about your sleep. It's simply a relaxing way to end the day.

// Start Here

Renew PEMF Mat

Full body, 6 coils, 1 to 30 Hz, four presets, heat from 0 to 70°C. This is the one most people start with.

See the Renew PEMF Mat, $995 →

PEMF Mat Cost: What Drives the Price

Here's what moves the number, based on what goes into building one.

PEMF mat cost covers a wide range, and pemf mats at very different prices can look alike in photos.

  • Size. A full-body mat costs more than a pad or pillow.
  • Coil count. More coils means more copper and more build cost.
  • Heat. An infrared heat layer, especially one with a wide adjustable range, adds cost.
  • Presets and controller. Fine frequency steps, presets and a clear controller cost more than a simple on/off unit.
  • Extra layers. Red light, negative ions and gemstone layers add to the price.
  • Build. Cover material, shielding layers, weight and certifications all matter for a mat you'll use daily.

Here's where our mats land (prices from our store at the time of writing):

  • Renew PEMF Mat: $995
  • Renew+ PEMF Mat: $1,349
  • Renew+ PEMF Pillow: $299

When you compare, look at the spec sheet first, then the price. A cheaper mat with no heat control and no presets is a different product.

Full-Body Mat vs Pillow vs Wrap

Which recovery mat format is right depends on how you'll use it.

Renew PEMF Mat

Full body, 6 coils, 1 to 30 Hz, four presets, heat from 0 to 70°C. This is the one most people start with. It's simple and it covers the whole body. Shop the Renew PEMF mat.

Renew+ PEMF Mat

Full body, 8 coils, 1 to 30 Hz in 1 Hz steps (no presets), plus 144 red LEDs at 660 nm and a negative ion setting (over 3,500 ions/cm³). Heat runs 30 to 70°C. It's the one for people who want every layer in a single session. See the Renew+ PEMF Mat.

RECON Renew+ PEMF Mat with 660nm red photon LEDs illuminated
The Renew+ PEMF Mat with its 660 nm LEDs on.

Renew+ PEMF Pillow

A 20 x 12 x 4 in memory foam pillow with 1 large coil, 35 red LEDs at 660 nm, 1 to 30 Hz and heat from 30 to 70°C. It goes under the neck, shoulders or lower back, and it's small enough to travel. Sessions run 10 to 30 minutes, and it's $299. See the Renew+ PEMF Pillow.

RECON Renew+ PEMF Pillow with red photon LEDs illuminated, side view
The Renew+ PEMF Pillow, the compact option.

Wraps

A wrap goes around one spot, like a knee or a shoulder. It's useful for a single area, but it's not a full-body session. We don't currently sell a PEMF wrap. For a single spot, the Renew+ PEMF Pillow is our compact option.

The RECON Wellness Human Performance System

PEMF is the second pillar. It follows compression and pairs with red light.

01
Activate / Circulate
Sequential air compression. The boots are where the routine starts.
02
RECON Renew
PEMF and adjustable heat for the wind-down after the boots come off.
03
Restore Red Light
Red and near-infrared light. Restore panels run 8 wavelengths.

PEMF Mats: Common Questions

A PEMF mat is a full-body surface with built-in copper coils that send a pulsing electromagnetic field at a frequency you choose. An infrared PEMF mat adds a far infrared heat layer to the same surface.
We run 20 to 40 minutes on the Renew. The Renew+ lets you set 20 to 60 minutes. Use the timer so it shuts off on its own.
We use it before bed, not all night. Set the timer for 20 to 30 minutes on the 3 Hz Wind-Down preset and make it part of your wind-down routine.
The Renew is adjustable from 0 to 70°C (32 to 158°F). The Renew+ runs 30 to 70°C (86 to 158°F). Start low and adjust to what feels comfortable.
On the Renew, start with the presets. We use 23 Hz Pre-Training in the morning, 10 Hz Everyday midday, and 8 Hz Unwind or 3 Hz Wind-Down in the evening. On the Renew+ or the Pillow, step to the same frequencies by hand. Our presets guide goes deeper.
Both full-body mats are built to lie flat in one spot. The Renew is 72.8 x 29.5 x 1 in and 37.4 lb, and the Renew+ is 34.4 lb. Each ships with a carrying case. If you want something you can travel with, the Renew+ PEMF Pillow is about 9 lb.
People use both terms for the same kind of product: a full-body mat with PEMF coils, and often heat. We call ours recovery mats because that's how we use them, as part of a daily routine.
Our Renew PEMF Mat is $995 and the Renew+ PEMF Mat is $1,349. Size, coil count, heat range, presets, extra layers and build quality drive the price of any mat.

The Bottom Line

Pick a mat with real frequency control, a heat range you can turn all the way down, and a size that fits you. Then use it. The best recovery tool is the one that's easy enough to become part of your day. For us, that's the Renew PEMF mat.

General information only, not medical advice.

Find Your Mat

Lie down, press a button, make it part of your day.

Shop Renew PEMF Mat Explore RECON Renew

Life is the Adventure. The Body is the Vehicle.